How To Installieren Eines Deck Ledger Board
Was Sie benötigen Das Hauptbuch ist einer der kritischsten Teile Ihres neuen Decks. Es wird am Haus befestigt und dient als Hauptstütze für den Teil des Decks, auf den Sie von Ihrer Tür aus gehen, sowie als Bezugspunkt, um den Rest Ihres Decks auszulegen. Da die Hauptplatine so entscheidend für die Erstellung eines strukturellen Decks ist, müssen Sie sicherstellen, dass die Hauptplatine richtig und sicher am Haus befestigt ist.
Was Sie benötigen
Das Hauptbuch ist einer der kritischsten Teile Ihres neuen Decks. Es wird am Haus befestigt und dient als Hauptstütze für den Teil des Decks, auf den Sie von Ihrer Tür aus gehen, sowie als Bezugspunkt, um den Rest Ihres Decks auszulegen. Da die Hauptplatine so entscheidend für die Erstellung eines strukturellen Decks ist, müssen Sie sicherstellen, dass die Hauptplatine richtig und sicher am Haus befestigt ist. Hier finden Sie eine Schritt-für-Schritt-Anleitung, die Ihnen hilft, die Hauptplatine für Ihr neues Deck richtig zu installieren:
Schritt 1 - Messen und Markieren
Markieren Sie die Position oben in Ihrem Deck gegen die vorhandene Verkleidung Ihr Haus. Dies sollte etwa 1 bis 2 Zoll unter der Innentürdichtung sein. Sie möchten keine zu große Entfernung zulassen, da sich Wasser, Eis oder Schnee ansammeln und in die Türdichtung eindringen können.
Schritt 2 - Mehr Messen
Zeichne eine Linie, die die volle Länge deines neuen Decks angibt. Achten Sie darauf, dass Sie die kombinierten Dicken der Terrassendiele sowie die Breite der Hauptleiterplatte berücksichtigen, die an Ihrer Außenwand befestigt wird. Für unser Beispiel verwenden wir 2-mal-10 Stück behandeltes Schnittholz für unser Hauptbuch. Daher müssten wir 1-1 / 2 Zoll für die Terrassendielen und weitere 9-1 / 2 Zoll für das Ledgerboard messen, was insgesamt 11 Zoll betragen würde. Verwenden Sie anschließend eine Kreidelinie, um eine gerade Linie zwischen den beiden Hauptpunkten zu erstellen.
Schritt 3 - Abstellgleis entfernen
Schneiden Sie mit der Kreissäge entlang der gezeichneten Linien und schneiden Sie die Abstellgleise aus dem Haus heraus. Vergewissern Sie sich, dass die Dicke der Klinge gerade so groß ist, dass nur das Seitenprofil geschnitten wird. Verwenden Sie dann Hammer oder eine Hebelstange, um die Abstellgleise zwischen den beiden markierten Linien aus Ihrem Haus zu entfernen.
Schritt 4 - Ausrichten der Hauptplatine
Platzieren Sie die Hauptplatine so, dass die untere Kante der Hauptplatine richtig mit der Unterkante der Aussparung ausgerichtet ist. Sie können ein paar 16 Penny Nägel, die teilweise eingetrieben werden, verwenden, um die Hauptplatine an Ort und Stelle zu halten. Diese Nägel sind temporär, also vergewissern Sie sich, dass Sie sie nicht vollständig antreiben.
Schritt 5 - Bohren von Löchern
Bohren Sie Löcher durch die Hauptleiterplatte in die Seite des Hauses für die später einzubauenden Zugschrauben.
Schritt 6 - Entfernen Sie die Ledger-Platine
Entfernen Sie die Ledger-Platine aus dem Haus dann und drücken Sie und fügen Sie Silikon-Dichtung in jedes vorgebohrte Loch. Das Silikon fungiert als Feuchtigkeitsabdichtung für die Bereiche, in die Zugbolzen eingesetzt werden.
Schritt 7 - Befestigen Sie die Hauptplatine
Setzen Sie die Hauptplatine wieder in den Ausschnitt des Hauses und befestigen Sie sie mit Hilfe von Zugschrauben sicher an der Seite des Hauses. Stellen Sie sicher, dass die Zugschrauben sehr fest angezogen sind, und sichern Sie so die Hauptplatine.
Schritt 8 - Hinzufügen von mehr Silikon
Verwenden Sie Ihre Dichtungspistole, um eine große Silikonwulst über die Oberseite der Hauptplatine zu führen.
Schritt 9 - Installieren Sie das Flashing
Verwenden Sie das verzinkte Flashing unter der freiliegenden Verkleidung und über der Oberseite der Hauptleiterplatte, um zu verhindern, dass Wasser zwischen dem Haus und der Hauptplatine eindringt.
Schritt 10 - Abdichten und Fertigstellen
Füllen Sie nach dem Einbau des Blinkens alle Spalten oder Spalten mit Silikonabdichtung aus. Sobald das Silikon getrocknet ist und Sie überzeugt sind, dass das Deckblatt nicht undicht ist und sicher befestigt ist, können Sie mit den anderen Schritten beim Aufbau Ihres Decks fortfahren.
FAQ - 💬
❓ How do you attach a ledger board to a deck?
👉 0:142:19How to Install a Ledger Board for a Deck - DIY NetworkStart of suggested clipEnd of suggested clipTo install it first mark where the top of your ledger board will sit against the house. Then removeMoreTo install it first mark where the top of your ledger board will sit against the house. Then remove the siding in this area.
❓ How far apart should lag bolts be on a ledger board?
👉 The bolts or lags must be placed along the ledger in two rows-one row along the top and one along the bottom-with the fasteners staggered between the two rows at the spacing indicated by the IRC table. For example, on a deck with a joist span of 15 feet, the lag screws are spaced 11 inches apart.
❓ How do you waterproof a ledger board?
👉 Squirt a bit of gutter caulk or silicone sealer to seal any joints that don't overlap 4" or more. At this point, you can also caulk the inside corner of the ledger. Slip the bottom piece of siding under the next-to-bottom piece.
❓ Do ledger boards need to be pressure treated?
👉 Installing the Ledger Board The lumber for the ledger and all framing members must be pressure-treated for exterior use. The ledger will establish the height of your deck. This is an absolutely critical connection and must be installed properly to ensure the strength and safety of the deck.
❓ Can you attach ledger board to studs?
👉 MiTek's WSWH Washer Head Structural Wood Screw can be used to attach a ledger to studs directly, through 1/2" APA rated sheathing or through one or two layers of 5/8" gypsum wallboard (drywall).
❓ How much weight can a ledger board hold?
👉 The ledger is 10' long so every foot of ledger must be designed to carry at least 200 lbs of load.
❓ Should I pre drill for lag screws?
👉 You must drill pilot holes so that you do not splinter the wood or damage the lag screw. Any screw with a large diameter needs a pilot hole for easier and quicker installation. Drilling a pilot hole ensures that your lag screw won't break when you install it with a power drill. Torque can snap the head right off.
❓ Can I use lag screws for ledger board?
👉 7:0215:31Options for Fastening a Deck Ledger
❓ What do you flash treated lumber with?
👉 Copper works well because it is compatible with the chemicals used in commonly sold ACQ-treated lumber and is easy to bend.
❓ Is joist Tape Necessary?
👉 In order to protect your deck's substructure from weathering and moisture, protective tape for your joists is a must.
❓ Should you leave gaps between decking boards?
👉 The amount of space between deck boards should be anywhere from ¼” to 3/8” inch. You want plenty of space for water to flow between the boards and to allow small debris to fall to the ground. Deck board spacing greater than 3/8” of an inch can become problematic.
❓ Why install a ledger Board on a new deck?
👉 Because the ledger board is so crucial to creating a structurally sound deck, you must ensure that the ledger board is positioned properly and securely attached to the house. Therefore, here is a step-by-step guide to help you correctly install the ledger board for your new deck:
❓ Do you have to remove siding for a deck Ledger board?
👉 For any home project, be certain to follow local code and permitting requirements. The siding on the house will need to be removed before installing the deck ledger board. Make sure to remove enough siding to be able to install the back flashing above the ledger board and below the ledger board.
❓ How do you install a ledger board?
👉 Cut the boards to the desired lengths. Make sure the crown (the upward curvature of the growth rings) of the ledger board points up. Hold the ledger in place with nails. 5. Because a ledger board is very heavy and hard to work with, you need to drive framing nails (16 penny) or screws every two feet to temporarily attach the ledger.
❓ How do you attach deck boards to the House?
👉 Note: The deck boards have been depicted with a gap between the first board and the house only to emphasize flashing overlapping the ledger. On site the first board would be positioned within 1/2" from the wall flashing. In this second method, 1/2" through bolts are used to anchor the band board and ledger together.